Yay! Most tools arrived. Check it out! Its like Christmas again...
First up, back rivet plate, flexible lightweight air hose, and maroon scotch write pads. Then air hose is really nice. I'm glad I got it. Definitely would recommend picking one up if you haven't got one yet.
Filing kit (VERY NICE!) 24" ruler, RV-10 Elevator bucking bar, 12" drill bit (looks like #30 is pictured.
The brush is I believe to clean the files..
Tungsten bucking bar, 3X rivet gun, flush set, drill bits, quick change chuck and kit, sioux 6000RPM drill (VERY nice, small, lightweight), assorted rivet sets.
Cleco 1" clamps, Cleco .5" clamps, step drill bit, reamers, mini scotch write wheels, and more....
Fluting pliers, Medium scotch write wheel, fine scotch bright wheel, seamer, countersink cage x2, and more...
So yes, got many tools in. Finally the tools are in. Now I can get a move on the build. But first, I need to learn to use the new tools. More specifically, the ones that can cause more permanent damage. Waiting on the 2 practice kits from Vans Aircraft. Stay tuned.... more to come.
This blog was created to document the adventure of building a Vans RV-10 Experimental Airplane in my garage. It serves as proof that I built it as required by the FAA.
Tuesday, May 31, 2016
Monday, May 30, 2016
Another day without the REST of the TOOLS....
Picked up a HVLP gun at Harbor Freight for 13 bucks. It's shipped with the needle with some sort of grease. Pulled the needle out, cleaned it with mineral spirits. Ran some 50/50 mineral spirits and water through the gun to clean out any thing else it may have that I couldn't reach with the tiny brush cleaner it came with. I also ran acetone thru it to clean it up more and have it dry quickly. Next...Need to wait for the TOOL KIT to ARRIVE so use the scotch brite pads to scuff up the elevators to prime with AKZO to move one to final assembly.
Throughout the day, I skipped around in the plans minus the empennage attachment section and fabricated all the pieces minus deburring. Thats the pile of parts completed today. I couldn't find anything else to make or do so this was the last of the work until the tools arrive.
This is my first mistake! I cut ALL the tail cone J-channels incorrectly. The J-channel in front is cut incorrectly. The one behind is curt correctly. This really took a toll on me. But mistakes happen and I will learn from this for sure. Check and check, and check 5 more times before you cut. Minor detail but still it's wrong. I was able to use all the long (already cut wrong) J-channels and repurpose them for the shorter J-channels called out in the plans. I'll call vans in the morning and order new 8' j-channels.
This is the correct cut, straight on the flat part, 45 degree not the J
Thats it for now till the tools arrive.....lol
Sunday, May 29, 2016
Still waiting on tools. Its Sunday and no one is delivering today. Not UPS, not FedEX, not USPS, NO ONE. Oh well, I'll skip ahead on the plans and work on something else to make my time productive.
Picked up 3 hinges and a 2"X8"X 8' that the store cut in half for me. I could have made the cut at home but didn't wan't to whip out, setup the saw and make a mess for just one cut. Since I was in the sedan, it was easier to transport too, in the trunk.
Made a home made break per the plans. I put in the trim tab and bam, it was bent further. Not sure why its not bent to it's final angle from factory but oh well, done deal. I'll set the break aside in case someone wants to borrow it or till the next build....huh???lol. Oh did I mention I have been loving the build process so far. Totally up my alley.


Next up was to bend down the trim tab "tabs". I clamped the skin tight with a c-clamp using wood to protect the skin. I used a 1/2" scrap piece of plywood about 4" long 2" wide and went at it with a hammer. I layed the end of the plywood on top of the tab and hit the wood with the hammer firmly. Not blasting away at it but firmly. As the tab began to bend, the plywood just followed the angle till it was at the desired 90 degree bend.
I used 2 clamps to ensure the skin didn't move. I did all 8 tabs this way. Easy peasy.
Next, I cut the elevator counter balance weights. The band saw made quick work of this task. Since lead can be nasty, I dawned the safety glasses and respirator.
Yup, thats me. Glad I had the safety gear on, The lead was everywhere despite the vacuum connected to the band saw.
Saturday, May 28, 2016
After spending all morning and most of the afternoon building 2 more tables, I had to put in some time in fabricating airplane parts. After all, this is about building an airplane right!
Trim Tab Horn
Removed the shaded area using the band saw. Still need to debur, waiting on scotch bright wheel.
Still waiting on the bulk of the tools and with nothing to do left on the elevators or elevator trim tabs, started looking over the tail cone section. Searched for small band saw related work or stuff I could do with the tools already on hand.
Tables
After clecoing together the elevators I quickly found out I needed more workbench space. Having the right elevator on a wobbly folding table didn't feel right. The foldout table was very narrow having just enough space for the elevator.
Built a 2nd EAA style work bench, added the shelf to the bottom of both EAA tables.
Built a rolling power tool worktable EAA style. Dimensions on the top is 28" long by 21" wide. Also with a shelf at the bottom. This will house the drill press, vise, band saw, and bench grinder. All the power cords were routed neatly with zip ties to the side then underneath to a 14ga 2ft 3 plug extension. 2 of the 4 wheels have brakes. The wheels make is ver easy to move around. This freed up the tool bench top. Oh made of 75% wood laying around from other projects as you can tell from the semi painted parts.
A Few More Tools
Still Waiting on the shipment of the main tool set. While going through the elevator section, I realized a small ruler would be nice to have. Flipping through the cone section, an angle finder would be nice to have to match up the angles on the band saw. Picked them up from the local hardware store and used them right away. The main tool kit will come with a 24" ruler. The 6" will be nicer for shorter measurements. It can measure down to 1/64ths.
The CDI 20-150 in-lb torque wrench came in today via USPS on Saturday. Love it when packages come in the mail. The excitement never goes away to open up a package even thought I know whats inside, lol.
Friday, May 27, 2016
Updates on Vertical Stab
The blue stuff I found around some of the rivets was blue tape put on the flat rivet set to prevent marring of the skins. So that is a non issue now.
Next, this is the email reply from vans regarding the rear spar cap doubler:
This gap looks to me like they missed a step in dimpling/countersinking and you may possibly have a dimple sitting on a flat piece to create this gap. It could also just simply be that when this part was match drilled to the spar it was not clamped tight against the flange. Either way this is not a very desirable situation. I would recommend you dismantle and fix.SterlingVan's Aircraft
I'll drill out the left side of the spar cap to make sure there are dimples. Next I'll put plenty of clamps down to keep the cap flush to the spar then rivet. I'll put this on hold for now until I have some experience under my belt with drilling out rivets.
Subscribe to:
Posts (Atom)





















